If your iPhone 13 Pro screen is cracked, unresponsive to touch, or doesn’t display pictures when you turn it on, use this guide to restore your iPhone to normal operation using a new screen (also known as a display assembly).
Note: True Tone and Auto Brightness are disabled after screen replacement, even with an original Apple screen. Face ID is also disabled unless your iPhone is running iOS 15.2 or later.
On iOS 18 and later, you can use Apple’s Repair Assistant to calibrate a new screen to restore True Tone display on a genuine screen purchased from Apple. If your iPhone 13 Pro screen is cracked, unresponsive to touch, or doesn’t display pictures when you turn it on, use this guide to restore your iPhone to normal operation using a new screen (also known as a display assembly).
Note: On iOS 17.6 and earlier, True Tone and Auto Brightness are disabled after screen replacement, even with an original Apple screen, unless your iPhone is running iOS 15.2 or later. On iOS 18 and later, you can use Apple’s Repair Assistant to calibrate a new screen to restore True Tone display on a genuine screen purchased from Apple.
Step 1ļ¼Pentalobe Screws
Note: Before proceeding, reduce your iPhone battery to below 25%. Accidental puncture could cause a charging lithium-ion battery to catch fire and/or explode.
Power off your iPhone before beginning disassembly.
Remove the two 6.8mm long pentagonal P2 screws located on the bottom edge of your iPhone.
Opening the iPhone display will compromise its water seal. Have a spare seal prepared before performing this step, or if reassembling the iPhone without replacing the seal, take care to avoid liquid exposure.
Step 2: Gently lift the screen
Use the suction cup at the bottom edge of the phone, avoiding the edge of the glass.
Pull the suction cup upwards with steady, constant pressure to create a tiny gap between the front panel and the back cover.
Insert the pry tool into the gap.
The waterproof adhesive between the screen and the bezel is very sticky and requires considerable force to pry open even slightly. If you have difficulty opening the gap, continue heating and gently shake the screen up and down to soften the adhesive strip until a sufficient gap is created to insert the tool.
Step 3: Heat the right side
Heat the right edge of your iPhone with a hairdryer for 90 seconds, or until the screen is slightly warm to the touch.
Step 4: Separate the adhesive on the right.
Slide the triangular pry tool along the bottom right corner of the iPhone to loosen the glue.
Continue sliding upwards along the right edge of the iPhone until you reach the top right corner.
Do not insert the pry tool more than 3 mm into the iPhone, as this may damage internal components.
Leave the pry tool in the top right corner of the phone before proceeding.
Step 5: Cut open the waterproof adhesive on the left side
Insert the second triangular pry tool into the bottom left corner of the iPhone.
Twist both pry tools simultaneously until the latch on the left side releases.
The twisting action should be gradual.
If the waterproof adhesive is difficult to remove, you can heat the left edge again.
Step 6: Remove the battery interface cover
Use a Y000 screwdriver to remove the three 1.3 mm screws securing the battery connector cover.
Throughout the repair process, trace each screw and ensure it is accurately returned to its original position to avoid damaging your iPhone.
During reassembly, this is a good time to open the iPhone and test all functions before sealing the display in place. Always ensure the iPhone is completely powered off before continuing.
Step 7: Disconnect the battery
Use a pointed pry bar or a clean fingernail to pry the battery connector off the socket on the motherboard.
Try not to damage the black silicone seals surrounding this connector and its connection to other circuit boards. These seals provide extra protection against water and dust.
Slightly bend the connector away from the motherboard to prevent it from accidentally contacting the socket and powering the phone during repairs.
Step 8: Disconnect the monitor cable.
Use the tip of a pry bar or a clean fingernail to pry the monitor connector off the socket on the motherboard.
To reconnect such a snap-on connector, carefully align and press down on one side until it clicks into place, then repeat on the other side. Do not press in the middle. If the connector is misaligned, the pins may bend, causing permanent damage.
Step 9
Remove the display components.
